GO BACK Mow-Master Side Mounted Mowers

Rotary 36", 50", 60", 72"
  • Use for grass & brush - Handles up to 4" material
  • All decks interchangeable
Flail 50", 60", 75", 90", 102"
  • Deck Lift uses no cables or pulleys
  • Uses Direct Cylinder Lift

Specifications
Side Mounted Mowers

1. 36", 50", 60" & 72" cutting widths, rotary, hydraulically driven.
2. Blades - 2, 3, 4, or 6 full swinging offset.
3. 7 1/2" solid steel spindle, machined to fitness.  11" long with 3 1/4" lower bearings & 2" upper bearing.
4. Full length replaceable skid shoes.
5. Deck 3 piece for easier repair, with 3/8" sidewalls and 3/16" top.
6. Spindle - mounted in double taper roller bearing seal, with oil bath.
7. Blade carrier disc with 2, 3, 4, or 6 offset knives - grade #1045 steel, 5/8 x 31 1/2", 60" & 72" decks only, with 5/8" grade 8 bolts attaching to spindle and using 1 1/8" blade bolts.
8. Cast iron steel motor - gear type.
9. Direct lift, no cables.
10. 125" reach from tractor center.
11. Free - floating linkage on cutting ass embly.
12. Main control valve - nonrestrictive, electric solenoid type.  Starter lockout switch and hydraulic brake.
13. Hoses - 1 1/2" ID suction, 1 1/4" ID return.
14. Hydraulic reservoir - 65 gallon oil equipped in tank 75 GPM, 25 micron filter with restriction gauge.  Tank will have ball valves on suction and return outlets.
15. Cast iron hydraulic pump - gear type, front engine mounted.
16. Pump drive shaft from crankshaft of engine rated at 180 HP.
17. Deck - working ARC 165°.
18. Replaceable steel bushings all pivot points.
19. Spindle RPM - 1900 RPM.
20. Two spool valve, stand and hoses.
21. Flex coupler between motor and blade spindle and is shielded.
22.  Mower and deck capable of handling 4" material without excessive wear.
23. Equipped with 4 ply rear guard.
24. Main frame anchored to rear axle and to from casing.
Options: 
  • Chain guards rear and/or front
    (Rear chain guards required for Industrial use.)
  • Remote cable control to eliminate hoses in cab (recommended)
  • Rear PTO pump.
  • High pressure hydraulic system.  Using 1 inch hose.
  • Flail head.
  • Ditcher head
  • 3/4" blade dish
  • Stump jumper blade dish

Specifications
Flail Heads

1. Cutter width - 50", 60", 75", 90" or 102".
2. Cutter Assembly - Hydraulically driven 2,200 RPM.
3. Cutter Shaft - Dynamically balanced, 6' diameter.
4. Side Plates - 1/2" wall drive side - 3/8" on outer end both with 2-3/16" bearing carriers.
5. Knife Swing Circumference - 62 1/2"
6. Roller - adjustable 0-6" full length tie-rod type, with contoured ends: 6-5/8" diameter with 1-3/8" grease type bearings
7. Cutter Head - 1/8" bonnet.
8. Skid Shoes are removable.
9. Interchangeable with Rotary heads & Ditcher head.
10. Drive Belt - double C belts, 90 HP rated.
11. 50" Flail - 52 reversible general purpose knives or 26 H.D. 2-1/2" cup knives.
12. 60" Flail - 60 reversible general purpose knives or 30 H.D. 2-1/2" cup knives.
13. 75" Flail - 76 reversible general purpose knives or 38 H.D. 2-1/2" cup knives.
14. 90" Flail - 96 reversible general purpose knives or 48 H.D. 2-1/2" cup knives.
15. 102" Flail - 104 reversible general purpose knives or 52 H. D. 2-1/2" cup knives.

greenline.gif (3043 bytes)

boom mower side mounted mowers 3 point mowers ditcher attachments
Picture Gallery Homepagedealer inquiries Contact Us
Mow-Master Roadside Mowers meet SAE J232-1984 Standards!

Dealer inquiries welcome!  Call, write or e-mail us!